90% – 95%* Removal efficiency *Dependent upon input material and/or SOP. 50c – 85c Operational evaporator temperature. Throughput. With its unique design, the FFE-Series Falling Film Evaporator greatly increases the throughput of botanical oil production boasting an impressive 45-60 gallons per hour of alcohol recovery. Separation.
More details
A Falling Film Evaporator (FFE) is a combination of vertical shell and tube heat exchanger and vapor- liquid separator mounted at bottom. The feed is given at top of shell tube type heat exchanger having distributor. The liquid falling on distributor get distributed in such a way that it flow down as a thin film on inside surface of the tube.
More details
Evaporation in our 60 kW Falling Film Evaporator happens at nearly 20 times the speed of a 20L rotary evaporator. The oil and solvent mixture is pumped into the top of the Falling Film Evaporator where it is dispersed over the tube openings. As the mixture falls down the inner surfaces of the heated tubes, the solvent boils off by the time it ...
More details
falling film evaporator. For the processing of fruit, we make lines for all types of continental tropical fruit: with stone, without stone, citrus fruit, tropical fruit. The scheme refers to a line with maximum flexibility but not optimized for specific products. ... Compare this product Remove from comparison tool.
More details
Falling film evaporators are vertical shell and tube heat exchangers. Typical TEMA types are BEM, NEN or a combination of the two. The major difference between a typical shell and tube heat exchanger and a falling film evaporator is the liquid distribution at the top of the unit. Liquid entering the top of the unit passes either through a spray ...
More details
In falling film evaporators, the liquid product usually enters the evaporator at the head of the evaporator. The liquid enters the heating tube and forms a thin film on the tube wall where it flows downwards at boiling temperature and is partially evaporated. In most cases, steam is used for heating the evaporator.
More details
In vertical falling film evaporators the tube length is . The tube length is typically 6 m to 11 m (20 ft to 36 ft) but can be as short as 1.5 m to 3 m (5 ft to 10 ft) for example in deep vacuum applications. Diameters are typically 20 mm to 64 mm (1 …
More details
It consists of solar collectors, vertical plate falling film evaporator and condenser, and the water storage tank and other components. Where the riser evaporator and condenser are assembled in the same chamber, this is an evaporation–condensation chamber. Vertical plate evaporator and condenser have many forms; in order to make a film on the ...
More details
May 01, 2021 In falling film devices, this process happens at the liquid-vapor interface. It means that the device can use a lower temperature, meaning less energy use and some other benefits. For example, as there is no nucleate boiling on the tube walls, the solution in the evaporator will not crystalize. These long-tube devices are very energy efficient ...
More details
Mechanical vapor compression and falling film evaporators are suitable for volumes of up to 4,000 L/h per modular unit. These evaporators produce practically no foam, due to their high-performance separator. The internal division in the hot and cold zones reduces wear in the control and regulation equipment. The cleaning system integrated into ...
More details
Our falling film evaporator is specifically suited to process your products with a low viscosity and a low tendency for fouling. It consists of a tube bundle crowned by a proprietary liquid distribution device that ensures an efficient and uniform distribution of the liquid to all the tubes. Your product flows as a continuous film along the ...
More details
the descending film, flow with the concentrate into the sump of the falling film evaporator and are conducted as steam to the external condenser for condensation. As a result, the distillate flows out of the condenser. Meanwhile, the non-evaporated liquid flows along the fal-ling film evaporator tubes, is continuously concentrated by
More details
The Falling Film Evaporator (FFE) has its own take on the technology, incorporating improved features that keep the operator in mind. As a large portion of the tincture processed using a falling film evaporator is coming from a cold ethanol extraction, the design takes advantage of the cooling power that is already a sunken cost in the form of the electricity used to generate it.
More details
Tube Falling Film Evaporator: versatile and efficient. GIG Karasek offers tube falling film evaporators for standard applications and with smaller evaporation capacities.
More details48-hour idling test machine before leaving the factory. You can take the materials to the factory test machine. We will customize the solution according to your needs.
HeadOffice Address
Zhengzhou, China
Equipment purchase
Get a Quick Quote
Send Us Email
[email protected]
Copyright © 2022 Jaunpur Machinery Company All rights reserved sitemap